8 Tips for Extending Punch Press and Punch Tool Life

The article's author, a metal fabrication professional, not only talks about best practices of maximizing punch tool and machine life, sharing his tips, but also gives an insight into the process of punching itself and some significant matters that need special attention in order to achieve the best results.

The article's author, a metal fabrication professional, not only talks about best practices of maximizing punch tool and machine life, sharing his tips, but also gives an insight into the process of punching itself and some significant matters that need special attention in order to achieve the best results.

They say you can’t fit a square peg in a round hole. Well you can of course, if you wallop it hard enough, but you shouldn’t. Hammer on that peg and you’ll damage both it and the hole while the hammer will spring back at you with surprising force. Metal punching involves pushing pegs, (the punches,) into holes, (the dies.) Between the two there’s a sheet of metal that the punch makes a hole through. If punch and die aren’t aligned you are doing that square-peg, round-hole thing and tool life and machine life will suffer.

The Punching Process

Most sheet metal fabrications pass through a punching process. This adds the holes needed to make the fabrication useful. (Cable entry points, for example, or locations for push buttons.) Simple punch press machines make one or more holes per stroke, (depending on how many punches are in the tool.) A turret punch on the other hand can “nibble” to create complex curves.

Edge Quality

The physics of punching metal is complicated. Basically, the punch deforms the metal until it cracks or shears. The goal is to get a smooth edge with no burr. Just as with our peg-and-hole analogy, how the punch and die fit together affects edge quality. It also influences the loads on the punch press, which affects how long it will last.

Looking after the Tools

Punching is integral for many fabricated metal parts. Taking good care of the tools keeps them cutting cleanly and smoothly. That results in better edges and extends the life of punches, dies and the machines themselves. It’s attention to details like these that keeps us at the top of our game. Let us look into some tips that can help maintaining the longest tool and punching machine life possible.

1. Maintain perfect alignment

Punch and tool must be lined up in x and y as well as rotation. Ideally the tool should be guided over its full stroke to prevent deflection. A good stripper system helps a lot in this regard.

2. Use correct clearances

Clearance between punch and die must suit the material being worked. Stainless needs a clearance of up to 20% of material thickness while the figure for copper is 12- 16%. Mild steel and aluminum are between these two.

3. Keep tools sharp

Repeated use rounds the edges of the punch. This increases the force needed to push through and creates larger burrs. Best practice is to regrind punch tools at frequent intervals, taking off the minimum necessary each time. (Edge radii should never exceed 0.004”.)

4. Lubricate

As the punch moves through the material friction generates heat. That can lead to galling (a build-up on the punch,) which reduces clearance and tool sharpness. A punch lubrication system is the best answer, but lubricating the sheet is a close second.

5. Use coated tools

A thin layer of gold-colored titanium nitride (TiN) or blue-gray titanium carbonitride (TiCN) reduces friction and wear. That keeps temperature down which, like lubrication, reduces galling.

6. Match the tool to the material

Think beyond A2 tool steel, especially when punching the new high strength alloys. A tough sheet metal needs a tough punch but for an abrasive material a wear-resistant steel may perform better. The modern M2 and M4 materials may be good choices.

7. Consider tool design

Grinding shear angles onto punch faces reduces punching forces and the load on the machine, (although it complicates sharpening.) Likewise, a back taper along the flanks can reduce friction. In general, make punches as thick as possible with the largest feasible radii under the head.

8. Practice good tool storage

Careless storage results in damaged tools. Always ensure tools are put away in a manner that protects them from damage. Clear labeling is good practice too.

Author: Ben Wiley

IMA information

Following the advise that the article above has just shared is especially useful when your machines are specifically chosen to match manufacturer's shopfloor processes. With Italian Machinery Association you can be sure the punching machines will be chosen, keeping that in mind. The best Italian manufacturers, members of IMA, offer their widest solutions to satisfy your needs.

Please also read the other materials about punching machines here:

Ready for a New CNC Machine? Key Factors to Consider

Comparing sheet metal techniques: what to choose?

The added value of punching machines

You also might need some repair, installation, re-launch or training services for your existing machines. IMA‘s maintenance team has enough skills and experience to solve any problem you might have.

Any other questions or inquiries? Don’t hesitate to contact us via phone/e-mail or visit us in any of our offices.

Other publications
6 criteria for choosing a grinding machine
There is a situation in the market of metal grinding machines in which participants want to get the maximum effect from the new equipment with minimal investment. The effectiveness of investments is evaluated not only by the price of equipment, but also by operating costs. And all this with limited funding.

We are constantly looking for new equipment suppliers, taking into account these and other market demands. That's why we settled on cleaning equipment from EMC.
Latest Developments in Sheet Metal Fabrication: 4 Key Trends
The worlds of sheet metal and ductwork fabrication are already experiencing significant disruption due to four groundbreaking innovations.
The Panel Bender: Your Ultimate Guide

Looking to improve production efficiency and reduce labor costs? Look no further than panel benders.
These machines, which have been around for over 40 years, offer a range of benefits over traditional press brake machines, including labor-saving and speed, good repeatability and consistency, and the ability to smoothly complete the positioning of the sheet in a single pass for four-sided bending.

Order a call

Full Name: *

Phone: *